AT28C64, 28C64 Datasheet, 28C64 64K ns Parallel PLCC EEPROM Datasheet, buy 28C 28C64 datasheet, 28C64 pdf, 28C64 data sheet, datasheet, data sheet, pdf, Atmel, 64K 8K x 8 CMOS E2PROM. 28C64 64K (8K x 8) CMOS E2prom with Page Write and Software Data Protection Features. Fast Read Access Time ns Automatic Page Write Operation.

Author: Shaktilabar Kagazahn
Country: Sudan
Language: English (Spanish)
Genre: Medical
Published (Last): 26 February 2010
Pages: 177
PDF File Size: 16.34 Mb
ePub File Size: 7.60 Mb
ISBN: 134-6-26483-354-9
Downloads: 63570
Price: Free* [*Free Regsitration Required]
Uploader: Shaktigis

Initializing pins for write I understand the benefits of separating the code into subroutines and will probably do this, but for now I am just trying to get the byte write working. Post as a guest Name. Thanks for dataeheet response, supercat. When the timer expires, an internal write cycle is triggered and additional writes before it completes.

eatasheet One thing that is missing is on page 7 of the datasheet, it states that you need to write a sequence of codes to disable write-protection. Here is the serial output. Home Questions Tags Users Unanswered.

28C64A-15 – 28C64A 64K 150ns Parallel EEPROM Technical Data

By using our site, you acknowledge that you have read and understand our Cookie PolicyPrivacy Policyand our Terms of Service. All behave the same.

Sign up using Email and Password. I am using the Xicor 28C64AP chip datasheet. I have tested an earlier version of the above program with a static RAM chip and everything works great. By clicking “Post Your Answer”, you acknowledge that you have read our updated terms of servicedatasueet policy and cookie policyand that your continued use of dwtasheet website is subject to these policies.


You have not indicated that you are doing anything with them? Email Required, but never shown.

I don’t really like the design, but my guess is that it was trying to be compatible with an earlier part where one could write locations one at a time and just wait after each one.

BTW, if the chips are equipment pulls as opposed to new parts, it’s possible that the “software protection” feature 2864 previously been enabled. Thanks for the info.

The device has 13 address pins, which should specify an address in binary from 0x to 0x1FFF. I’d 28c4 following that same sequence and also change your write sequence to follow the diagram on the following page.

28C64 Datasheet

Looking at the datasheet on page 12 it shows a timing diagram and Chip Enable Access Time can be up to nS. Since I am only using the eatasheet three address pins, the rest are tied low.

I added ms delays between every control pin datasheft and made sure the order was consistent with the datasheet, but still no luck. I have edited my question. Here is my code, sorry if it seems too cluttered: Sign up or log in Sign up using Google.

(Datasheet) 28C64 pdf – 64K CMOS EEPROM (1-page)

Also, I would suggest that you should write a writebyte procedure which sets all address and data wires to output and puts proper values on them, ensures WE and OE are deasserted, asserts CE, asserts and release WE, and releases CE, and a readbyte procedure which sets all address wires to output and puts proper values on them, sets all data wires to input, asserts CE and OE, samples all the data wires, and releases CE and OE. I have tied the top 10 address bits low and am only using the first 3 for now.


Dataheet 16k 20 42 The same diagram shows CE being asserted followed by OE for a read cycle. If it has, you’ll need to wire up all your address wires in order to disable it.

28C64 EEPROM Programming Using Arduino – Electrical Engineering Stack Exchange

Sign up using Facebook. The timings for this particular EEPROM aren’t super-critical, but it has a timer which datasyeet when the first byte is written and gets reset if another byte is written before it expires. Post Your Answer Discard By clicking “Post Your Answer”, you acknowledge that you have read our xatasheet terms of serviceprivacy policy and cookie policyand that your continued use of the website is subject to these policies.

Mar 26 ’13 at I wrote a program for the Arduino Uno that writes data to the first 4 addresses and then reads the data back.